Features:

• ARM926EJ-S ARM ThumbProcessor
  • DSP Instruction Extensions
  • ARM Jazelle Technology for Java Acceleration
  • 16 Kbyte Data Cache, 16 Kbyte Instruction Cache, Write Buffer
  • 210 MIPS at 190 MHz
  • Memory Management Unit
  • EmbeddedICE™, Debug Communication Channel Support
  • Mid-level implementation Embedded Trace Macrocell® (ETM®)
• Additional Embedded Memories
  • 32 Kbytes of Internal ROM, Single-cycle Access at Maximum Bus Speed
  • 160 Kbytes of Internal SRAM, Single-cycle Access at Maximum Processor or Bus Speed
• External Bus Interface (EBI)
  • Supports SDRAM, Static Memory, NAND Flash and CompactFlash®
• LCD Controller
  • Supports Passive or Active Displays
  • Up to 16 bits per Pixel in STN Color Mode
  • Up to 16M Colors in TFT Mode (24-bit per Pixel), Resolution up to 2048 x 2048
• USB 2.0 Full Speed (12 Mbits per second)
  • Host Double Port: Dual On-chip Transceivers, Integrated FIFOs and Dedicated DMA Channels
  • Device Port: On-chip Transceiver, 2 Kbyte Configurable Integrated FIFOs
• Bus Matrix
  • Handles Five Masters and Five Slaves
  • Boot Mode Select Option
  • Remap Command
• Fully Featured System Controller (SYSC) for Efficient System Management, including
  • Reset Controller, Shutdown Controller, Four 32-bit Battery Backup Registers for a Total of 16 Bytes
  • Clock Generator and Power Management Controller
  • Advanced Interrupt Controller and Debug Unit
  • Periodic Interval Timer, Watchdog Timer and Real-time Timer
  • Three 32-bit PIO Controllers
• Reset Controller (RSTC)
  • Based on Power-on Reset Cells, Reset Source Identification and Reset Output Control
• Shutdown Controller (SHDWC)
  • Programmable Shutdown Pin Control and Wakeup Circuitry
• Clock Generator (CKGR)
  • 32.768 kHz Low-power Oscillator on Battery Backup Power Supply, Providing a Permanent Slow Clock
  • 3 to 20 MHz On-chip Oscillator and two PLLs
• Power Management Controller (PMC)
  • Very Slow Clock Operating Mode, Software Programmable Power Optimization Capabilities
  • Four Programmable External Clock Signals
• Advanced Interrupt Controller (AIC)
  • Individually Maskable, Eight-level Priority, Vectored Interrupt Sources
  • Three External Interrupt Sources and One Fast Interrupt Source, Spurious Interrupt Protected
• Debug Unit (DBGU)
  • 2-wire USART and support for Debug Communication Channel, Programmable ICE Access Prevention
  • Mode for General Purpose Two-wire UART Serial Communication
• Periodic Interval Timer (PIT)
  • 20-bit Interval Timer plus 12-bit Interval Counter
• Watchdog Timer (WDT)
  • Key Protected, Programmable Only Once, Windowed 12-bit Counter, Running at Slow Clock
• Real-Time Timer (RTT)
  • 32-bit Free-running Backup Counter Running at Slow Clock
• Three 32-bit Parallel Input/Output Controllers (PIO) PIOA, PIOB and PIOC
  • 96 Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os
  • Input Change Interrupt Capability on Each I/O Line
  • Individually Programmable Open-drain, Pull-up Resistor and Synchronous Output
• Nineteen Peripheral DMA (PDC) Channels
• Multimedia Card Interface (MCI)
  • SDCard and MultiMediaCard™ Compliant
  • Automatic Protocol Control and Fast Automatic Data Transfers with PDC, MMC and SDCard Compliant
• Three Synchronous Serial Controllers (SSC)
  • Independent Clock and Frame Sync Signals for Each Receiver and Transmitter
  • I²S Analog Interface Support, Time Division Multiplex Support
  • High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer
• Three Universal Synchronous/Asynchronous Receiver Transmitters (USART)
  • Individual Baud Rate Generator, IrDA® Infrared Modulation/Demodulation
  • Support for ISO7816 T0/T1 Smart Card, Hardware and Software Handshaking, RS485 Support
• Two Master/Slave Serial Peripheral Interface (SPI)
  • 8 to 16-bit Programmable Data Length, Four External Peripheral Chip Selects
• One Three-channel 16-bit Timer/Counters (TC)
  • Three External Clock Inputs, Two multi-purpose I/O Pins per Channel
  • Double PWM Generation, Capture/Waveform Mode, Up/Down Capability
• Two-wire Interface (TWI)
  • Master Mode Support, All Two-wire Atmel EEPROMs Supported
• IEEE® 1149.1 JTAG Boundary Scan on All Digital Pins
• Package
  • LFBGA217, 217-ball LFBGA, 15 x 15 mm, pitch 0.8mm